обработка клинового выпада в задвижках с подъемом штока

Rising stem wedge gate valves are integral components of many industrial piping systems due to their excellent fluid control performance and wide range of applications. However, over extended periods of use, these gate valves may encounter corrosion, wear, or improper operation, leading to the failure of the connection between the stem and the wedge, which can cause the wedge to detach. This malfunction not only affects the normal regulation of fluids but can also lead to medium leakage, endangering equipment and personnel safety. Therefore, this article will delve into the causes of wedge detachment, the symptoms of failure, and the corresponding repair methods.

Failure Symptoms Analysis

During the use of rising stem wedge gate valves, wedge detachment is a common failure that typically manifests in several ways.

Valve Failure to Open: The valve cannot be opened by handwheel or other operations when closed, preventing fluid regulation and affecting production processes.
Medium Leakage: The seal between the wedge and the seat fails, potentially causing medium leakage, which can lead to environmental pollution and safety hazards.
System Downtime: After the wedge detaches, it may be necessary to halt operations for repairs, resulting in decreased production efficiency and economic losses.

Causes of Failure

The causes of wedge detachment are multifaceted and can generally be summarized into the following main factors.

Wear and Corrosion: Over time, the contact surfaces of the wedge and seat wear down due to friction from fluid flow or suffer a decline in sealing performance due to chemical corrosion.

Improper Operation: Incorrect operation methods, such as forcing the valve to close, can lead to the failure of the connection between the stem and wedge, and even cause valve damage.

Material Fatigue: In environments with high temperatures, high pressures, or frequent on-off operations, the valve materials may experience material fatigue, leading to the failure of connection points.

Design Defects: Irrationalities in valve design, such as an insecure connection structure between the stem and wedge, can also be a cause of failure.

Repair Methods

For the repair of wedge detachment in rising stem wedge gate valves, the following steps can be taken.

1. Preparation Work

Tools and Materials: Prepare wrenches, welding equipment, high-strength adhesives, threading tools, and manual tools.
Safety Measures: Before starting the repair, ensure there is no fluid flow in the system and take appropriate safety precautions, such as wearing protective clothing, gloves, and face shields, to avoid harm from accidental leaks.

2. Operation Steps

When dealing with the issue of wedge detachment in rising stem wedge gate valves, following a series of clear operational steps can effectively repair the malfunction. Here are the detailed steps.

Loosen the Bonnet and Stem Nut Bolts

First, remove the gland nut on the valve packing and loosen the packing. Then, loosen the nuts on all bolts of the bonnet one by one, but do not fully unscrew them to maintain some structural stability.

Check the Sealing Condition

Continue to turn the handwheel in the closing direction and observe the sealing condition between the wedge and seat. If there is medium leakage and the amount is not significant, proceed with the following operations.

Remove the Bonnet Assembly

Completely remove the parts above the bonnet and the stem to expose the top of the wedge. Carefully inspect the connection method and the cause of failure between the stem and wedge to facilitate the development of a targeted solution.

Repair the Connection

Withdraw the stem from the stem nut and packing gland, remove the handwheel and stem nut. For reconnection of the wedge and stem, welding is recommended, but exercise caution in oil and gas media to avoid fire or explosion risks. High-strength adhesives can be chosen, or after drilling and tapping the top of the wedge, connect it to the stem to ensure a secure connection.

Reassemble the Valve

Ensure the stem is perpendicular and well-aligned with the valve bonnet installation surface to prevent stem bending after repair. Install the bonnet, some packing, the gland, and the stem nut in sequence. Replace the sealing gasket if necessary to prevent leakage. After the bonnet is in place, align it with the valve body threads and tighten the bolts symmetrically, replenish the packing, and properly tighten the packing gland.

Maintenance and Preventive Measures

To ensure the stable operation and extend the service life of rising stem wedge gate valves, implementing effective maintenance and preventive measures is crucial. Here are some key recommendations.

Regular Inspections: Conduct regular maintenance and inspections of the valves, especially the sealing surfaces and connection points that are prone to wear, to identify and address potential issues promptly, extending the valve's service life.
Material Selection: When purchasing and replacing valves, opt for materials that are resistant to corrosion and wear to enhance the valve's service life and reliability.
Usage Monitoring: Monitor the valve's operating status in real-time to detect anomalies promptly and take measures to address them.

Conclusion

Rising stem wedge gate valves may face issues such as wedge detachment during use, but through reasonable repair methods, their functionality can be effectively restored to ensure the safety and stability of the system. Mastering the correct repair steps and precautions is essential for maintaining the normal operation of equipment. Furthermore, establishing a comprehensive maintenance mechanism and training system will further enhance the reliability of the valves, reduce the incidence of failures, and ensure the efficient operation of industrial systems.